Posted: September 11th, 2023
3.2 Lab Assignment: Fluids
Part 1 Gauge Pressure in Fluids
Initial Settings
· Open
PhET Simulation Under Pressure.
· Stay with the default Tab showing a rectangular pool.
· Check boxes: Ruler, Grid
· Atmosphere: Off
· Units: metric
· Fill the pool to the top using the spigot.
· Fluid Density and Gravity: Default values (1000 kg/m3 and 9.8 m/s2)
· Position the ruler so the 0
m mark is at the surface of the fluid.
Preliminary exercise.
· Position the pressure gauge at the very bottom of the pool.
· Take the reading and multiply it by 1000 to convert it to Pa units and record it in the table below.
· Imagine that you can measure the area of the bottom of the pool in square meters. Pick one of the following areas to use in your calculation:
Areas: 1.14 m2, 1.76 m2, 2.29 m2, 3.44 m2, 3.95 m2. Record your pick.
· Calculate the force exerted on the bottom of the pool using the pressure and the area values. Round your answer to the nearest whole number.
· Formula and example calculation:
Pressure ( 
Area ( 
Force (you provide the units) 
This is like problem 1 in the 3.3 Practice Problem set.
Simulation instructions
· Drag a pressure gauge from the tool area and place the tip of the gauge at your choice of depth.
Do not use 1.0
m, 2.0
m, or 3.0
m
.
· Move the Fluid Density slider up and down and observe how the pressure changes.
· Move the Gravity slider up and down and observe how the pressure changes.
· Set the sliders to any value except the default values, the extreme values of the slider, or the values used by the instructor.
· Record the depth (
h), liquid mass density (
D), gravity (
g), and pressure reading (
p) in the table below.
· Convert the pressure from
kPa to
Pa by multiplying the
kPa value by 1000.
· Calculate the pressure using the formula . Round your result to the nearest whole number.
· Change the units setting to
Atmospheres and record the pressure.
· Change the units to English and record the pressure in psi below.
Depth, 
Fluid Mass Density, 
Gravity, 
Pressure, 
Gauge Pressure, 

Calculated, 
Simulation: 
Simulation: 
Change the Atmosphere setting to “on” and notice your pressure gauge go up.
Place a pressure gauge at the surface of the ground.
Check that the gauge pressure due to the fluid alone (pressure found in Trial 2) plus the atmospheric pressure (in the same units as your gauge pressure) adds to the reading on the gauge under the surface of the liquid.
Does the shape of the container affect the pressure?
· Change the tab of the PhET
Under Pressure simulation to the 2nd tab showing the two linked pools with different shapes.
· Fill the pool to the top.
· Place a pressure gauge at the very bottom of the pool and move it to different places along the bottom from left to right.
· Answer the following question.
Put an “X” in the box next to your answer. 

a 
The pressure is greatest on the left side of the pool. 

b 
The pressure is the same at all points along the bottom. 

c 
The pressure is greatest on the right side of the pool. 
Part 2 Density
Mass Density from Mass and Volume
· Open the
PhET Simulation Density.
· Click on the middle tab (Compare).
· Set the Blocks setting to Same Mass (default).
· Adjust the mass slider to any value except the default value of 5.00 kg or either extreme of 1.00 kg or 10.00 kg.
· Record this mass in the table below.
· Measure the volume of one of the boxes (your pick) by placing the box in the water. If the box floats, click and drag the box to force it to be under the surface of the water. Note the volume meter reading on the left side of the pool and subtract 100 L from your reading. This is the volume of the box. Record the box volume in the table below.
· Calculate the box mass density using the formula: . Units of your answer should be kg/L. Be sure to include your units with each value in the table.
· Round your density to 2 places after the decimal.
This is like problem 4 of 3.3 Practice Problems
Volume from Mass and Mass Density
· Change the Blocks setting to
Same Density.
· Change the Density slider to any value except 1.0 kg/L, the default value (0.50 kg/L) or either extreme of 0.1 kg/L or 2.0 kg /L. Record this in the table below.
· Pick one of the boxes and record the mass indicated on the side.
· Do not pick the smallest box.
· Calculate the Volume using the formula, modified from the mass density formula: .
· Be sure to include units with your mass and volume measurements.
· Check your answer by submerging the box under the water and subtract 100 L from the Volume reading on the left side of the pool. If your box floats, be sure to use the mouse to drag the box under the surface before reading the volume.
Density (kg/L) 
Mass 
Volume 
This is like problem 3 of 3.3 Practice Problems assignment, except the practice problem uses weight and weight density and English units.
Mass from Density and Volume
· Leave the Blocks setting where it is (Same Density).
· Change the density slider to a different value (do not use either extreme or the instructor’s value).
· Record the density in the table below.
· Pick a different box than in the previous part (do not use the smallest box) and measure its volume and record it below.
· Substitute the density and volume into the formula for mass and record the result in the table below. This should equal the mass on the side of the box.
Formula:
Density (kg/L) 
Volume 
Mass 
Part 3: Pascal’s Principle
· Open the Simulation:
Pascal’s Principle Lab or use the link in the assignment.
· Click “Begin”.
· Using the arrows, adjust the radius of tube 1 and tube 2 to equal the values listed below by your name.
Student 
Tube 1 Radius 
Tube 2 Radius 
Instructor 
44 
30 
Baca, Jacob 
22 
50 
Bltom, Biniam 
24 
48 
Brion, Matthew 
26 
46 
Clevenger, Christopher 
28 
44 
Eldridge, Marcus 
30 
42 
Higgins, Sean 
32 
40 
High, Parker 
34 
38 
Jimenez, Serena 
36 
38 
Mejia, JeffreyLousie 
36 
38 
Mohibi, Hasibullah 
42 
30 
Poor, Travis 
44 
28 
Powell, Anniya 
24 
50 
Smith, Shawn 
26 
48 
Tanner, Anthony 
28 
46 
· Click on the pin and observe which way the balance shifts.
· Replace the pin and adjust the mass amounts on the left and right to try to reduce the shift in the balance.
· Repeat this process until you find masses on the left and right which result in no shift in the balance when the pin is removed. Record those masses along with the radius values in the table below.
· Make a screen shot of our simulation
with the pin removed
to show the balance. The shot should show the mass and radius values.
Paste Screen Shot here.
Tube 1 Radius 
Mass 1 
Tube 2 Radius 
Mass 2 
Calculate the pressure on the left and on the right.
The force is the weight of the mass, converted to standard force units:
The area is the area of a circle converted to square meters:
Put the results of your calculations below and calculate the pressure:
Side 
Force 
Area 
Pressure 
Left (Tube 1) 

Right (Tube 2) 
Do not round your force calculation.
Keep at least 6 figures to the right of the decimal when rounding your area.
Round your Pressure to 3 places to the right of the decimal.
The two pressures should be approximately the same.
Part 4: Fluid Dynamics Lab
Open
Fluid Dynamics Simulation or see link in Assignment.
· Click “Begin.”
· Set the Left Pipe radius to any value above 15.0 cm but not the maximum.
· Set the Left Pipe speed to any value above 8.0 m/s but not the maximum.
· Set the Right Pipe radius to any value above 12 cm but less than the Left Pipe radius.
· When the fluid moves through the pipe and readings are available, record the fluid speed through the Right Pipe and the pressure in both Left and Right.
· To read the pressures, click on the meter to enlarge the view.
Pipe 
Radius 
Fluid Speed 
Pressure 
Left (1) 

Right (2) 
Use the equation of continuity to predict the fluid speed in pipe 2.
Solve for .
Note: Formula for Area = No need to convert units to standard units. Like units cancel in the fraction. For that matter, no need for pi.
Simplified formula: , where R stands for the radius. You must square each radius.
Show the substitution into the formula of your values and calculate the result below. 
This calculation is similar to problem 5 of 3.3 Practice Problems. Problem 5 uses other units and gives you the area instead of calculating the volume.
Select the correct relationship between fluid speed and pressure. 

a 
When the speed increases, the pressure increases. 

b 
When the speed increases, the pressure stays the same. 

c 
When the speed increases, the pressure decreases. 
Make a screen capture of the simulation first. Include everything in the dotted line and make sure your simulation is maximum size.
Make a smaller screen shot of each enlarged pressure reading, starting with the gauge on the left.
Paste Screen Shot of the simulation here.
Simulation
Paste Screen Shot of the left gauge here.
Enlarged Left gauge
Paste Screen Shot of the Right gauge here.
Enlarged Right gauge
2
Place an order in 3 easy steps. Takes less than 5 mins.